
Easy DIY Shredder Cabinet
You know that feeling when your space is finally decorated & everything is in its place?
Yeah me either, but for a fleeting three minutes, it happens sometimes if I clean up really quietly & the toddler & four dogs are distracted with food or mud.
I was sitting in my home office after a good decluttering & organizing session when I noticed everything had a place except my ACCO paper shredder.
Have y’all see our home office makeover featuring DIY built-in shelving units & bench seating!?

If you have been following along with me for anytime at all you know that this is when my DIY light bulb went off… It was time to build a shredder cabinet!
Supplies:
- 1 Sheet ¾” Smooth Plywood
- Dowel Rod or Cabinet Legs
- 1 Small Door Pull
- Paint or Stain
- 1 ¼” Pocket Screws or Nails
- Wood Glue
Tutorial:
- First I measured my ACCO shredder to find the length, height & width. I have the ACCO ShredMaster PSX 10-06 verison & those measurements are: 15x15x10”

- Once we had the measurements ready we ripped a piece of scrap plywood into (6) pieces:
- (2) 15 1/2 “ x 24” for the sides
- (1) 14” x 24” for the back
- (¾) for the base
- (1) 16 ½ “ x 16 ½ “ top

- Next, I drilled pocket holes into the back piece on both sides where it will connect to the two side pieces

- To attach the sides to the back piece we used wood glue, pocket screws, & also finishing nails because my pocket hole drill bit plus the drill wouldn’t fit into the tight space

- After the two sides were attached, we added the base 1” up from the bottom using nails & wood glue

- Finally it’s time to attach the door to the front of the cabinet! Start by attaching the hinges to the cabinet first & then attach them to the side of the front door

- The top of the cabinet was easiest to install. We just centered it on the base & nailed it in from the top
NOTE: Where my shredder cabinet will be located is under a desk that is why my cabinet opens from the front. If you do not have to worry about something obstructing the top you could add the hinges to the top of the cabinet, so that the top can simply open & you can shred your paper that way.

- This last step wasn’t in the original plans but after standing the shredder cabinet upright we decided to add some fun legs. You can buy legs at your local hardware store, but we had a left over dowel from the DIY Curtain Rod & Dowel project
Our legs are 3” long & we simply screwed them in from the base of the cabinet

- Another last minute idea was to add a hole to the back of the cabinet for the cord to go through

I used a 1” woodboring bit to make the hole

Finishing: Easy DIY Shredder Cabinet
- Now comes my favorite part: FINISHING! I used some leftover white paint for the sides & door

- I got a little fancy with the top & decided to stain it in Minwax Mocca

- Lastly, I added a small knob we picked up from Lowes to the front

How cute is this cabinet yall!

It fits my ACCO shredder perfectly & takes up barely any space!

I think staining the top added a nice touch & the small knob is perfect.

Now my shredder has a home & my heart is happy!

Not only is my ACCO shredder absolutely necessary for getting rid of personal documents, but you can also reuse the shreddings!
Check out all our favorite office finds here!
Here’s a few ideas I love:
- Use shreds for packing delicate items or shipping
- Make your own paper
- Use it for stuffing pillows, dolls, etc
- Mix it in with mulch
- Use it to help start a bonfire
- Use it for Easter basket grass
- Paper mache projects
- Vase filler
- Fill gift bags
- Make paper clay
The possibilities are endless yall!

You can also find a video of this Easy DIY Shredder Cabinet on my Hometalk page!
Hi! How do I email subscribe?
Hi Denise! We are currently switching providers but it will be back up again soon!